lgnition Switch Warning Indicator Light IP67 RED LED Lamp Beads

lgnition Switch Warning Indicator Light IP67 RED LED Lamp Beads

Lgnition Switch Warning Indicator Light

When you start the vehicle, the instrument panel will light up an indicator light. Don’t worry, this means that all the subsystems of the vehicle are self-checking.

If the self-checking is completed, these indicator lights will go out. General hazard warning, some important function failure, this function does not have a corresponding special warning light, you need to determine the faulty part according to the maintenance manual. 

1. The meaning of the lgnition switch warning indicator light:

The lgnition switch warning indicator light is usually caused by the poor fuel combustion in the engine cylinder. In automobile design, in order to ensure that the engine is in good working condition and the normal working life of the engine, an oxygen sensor is designed and installed on the engine to monitor the combustion state of the engine.

2. What happens when the ignition switch warning indicator light turns red?

The lgnition switch warning indicator light is an indicator light for the working state of the engine, which is used to display the working state of the vehicle engine.

When the key door is opened, the lgnition switch warning indicator light is turned on after the power is turned on. During the vehicle self-checking, the lgnition switch warning indicator light is turned on for about 3-4 seconds and then goes out automatically, indicating that the engine is working normally.

If the lgnition switch warning indicator light does not turn on or stays on, it means that the engine has a mechanical failure and needs to be overhauled in time.

3. Is it safe to drive with the ignition switch warning indicator light on?

In either case, you should check the car. It may indicate a problem with the ignition switch, or a problem with the key used.

The problem with the ignition switch is usually a mechanical problem, it will prevent the key from turning you can try to clean the keyhole, but the switch may need to be replaced, or even the key may need to be replaced to solve the problem. If this light is on when you are driving, it may be the reason why the key can be verified again.

The indicator lights on cars generally have the following colors: red, yellow, green, blue, and white. These colors have the same meaning as the various levels of warning in our lives, indicating different degrees of severity.

Red: hazard indicator, stop immediately, the vehicle has major safety hazards.

Yellow: fault indicator, you can drive to the repair station with caution, the vehicle is faulty.

Blue: High beam indicator, indicating that the high beam is on.

Green: Function indicator, does not affect driving, indicate the working status of a certain device or needs to perform a certain operation.

White: The function indicator light generally indicates that the functions that are not related to driving are in the on the state, such as the air conditioner is on, the wind mode, the rear window heating, etc.

If there is any indicator of light demand or customized indicator light, we will design and produce it in a very short time, such as the lgnition switch warning indicator light. Please don’t hesitate to write us an email at inquiry@cnylin.com.cn.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name lgnition Switch Warning Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Windshield Indicator Light AUTO IP67 Yellow LED Lamp Beads

Windshield Indicator Light AUTO IP67 Yellow LED Lamp Beads

What is the windshield?

The term windshield is used generally throughout North America. The term windshield is the usual term in the British Isles and Australasia for all vehicles. In the US windshield refers to the mesh or foam placed over a microphone to minimize wind noise, while a windshield refers to the front window of a car.

What does the light mean?

The “Windshield Washer Fluid Level” Warning Light indicates that the level of the washer fluid is low and should be added to the windshield washer fluid tank as soon as possible. Windshield washer fluid is a mixture that contains both soap and antifreeze.

Can low windshield fluid cause check engine light?

A malfunctioning sensor, low tire pressure, low transmission fluid and so much more will cause the light to come on.

 How long does the windshield message indicator light guarantee?

If you buy the windshield message indicator light, FILN promises to replace it for free within 5 years. If you have any questions during this period, you can also consult our staff. We will try our best to solve your problems.

Is there a minimum order quantity for the message indicator light?

Of course not, If you need, we will also provide samples. If the quantity of samples you need is small, you need to pay the freight by yourself. But if the quantity is large, you need to pay the product cost and freight.

How much voltage does this windshield indicator light?

We have 3 volts, 12 volts, 24 volts, 30 volts, 120 volts, 240v, and 360 volts. We can do anything from 3 volts to 300 volts. But our 240V indicator is the most popular among customers, and many regular customers will place orders for the 240V indicator every month

Except for the different voltages, is there any current?

There are several types of current, 1A,2A,3Aand 30A, but the current has little effect on the function of the indicator light. The main difference is voltage and material

What color does the indicator light have?

Our pilot lights come in a variety of colors, such as red, yellow, green, blue, white… The red windshield indicator light is still the most popular and sells best.

Therefore, our main product is also red 4wd indicator light.

What is the difference between windshield indicator light housing?

The housing has plastic and metal indicator lights, such as it is the same size of 10 mm and the product parameters are the same. We have both metal and plastic.

And we also have two kinds of tape and pin. General customers will confirm before the next inquiry to bring the line of pins and plastic or metal.

How do we buy a windshield indicator light?

You can contact us directly, you need to fill in some of your information below, we will contact you directly after receiving the email.

After the communication, we will carry out the production. If you don’t know what products do we have, you also can visit our official website www.indicatorlight.com to know more information about the details.

How can I buy the indicator light?

You can contact them by email at WWW.INDICATORLIGHT.COM, FILN CAR INDICATOR LIGHT sales email inquiry@cnylin.com.cn, or buy directly from AliExpress and Amazon, though the prices are much better if you buy directly from a factory in China. If you send DHL to the United States, the freight will be about 20 DOLLARS, and the time will take 3 days.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Windshield Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Suspension Damper Indicator Light IP67 Red LED Lamp Beads

Suspension Damper Indicator Light IP67 Red LED Lamp Beads

24v 220v suspension damper symbol indicator light

The rapid development of our country’s economy has led to an increase in the per capita economic level of our people.

As the economic level improves, the quality of life will naturally become better. So over the past few years, more and more people have bought cars. Said that the car dashboard should be no small problem,

Today’s cars are highly intelligent precision electromechanical products that can run automatically after starting. In order to monitor the working status of each system, various sensors and electronic control units are installed in the car.

If a fault or abnormality occurs in a certain part, the corresponding fault light on the instrument panel will be lit to remind the driver to pay attention.

Because the automobile electronic control system is very complicated, the fault lights are also diverse, and it is difficult for ordinary people to recognize them.

But in order to avoid that when the indicator light is on, the driver does not know where the car is except for the fault, and should he continue driving, the necessary fault light symbols must be recognized. Now I will introduce you to the suspension damper symbol.

When the vehicle is started for self-inspection, the suspension damper fault indicator will light up. If the engine is working normally, it will automatically go out after starting.

If the engine failure indicator light is always on after starting, it means that the engine may have a mechanical failure. There are many reasons for the suspension damper fault light to be on. Generally, it is difficult to self-check and solves it. It is best to stop and perform professional inspections on time.

Yulin can also make suspension damper symbol indicator lights, available in sizes of 8 mm, 10 mm, 12 mm, 14 mm, and 16 mm. There are generally five colors of suspension damper symbol light LED lights, red, yellow, blue, green, and white.

If you want to make a suspension damper two-color lamp, Yulin can also make a suitable suspension damper two-color lamp according to your requirements.

The voltage of the suspension damper indicator light produced by Yulin Company is customized according to customer requirements, such as 12v, 24v, 36v, 110v, 220v, etc., can be made. The voltage range that our company can customize is 3v~380v.

Some customers need a small voltage, and some customers need a high voltage in the environment where the indicator light works, so the required voltage is high. Yulin took this into consideration and controlled the voltage customization range from 3v to 380v.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Suspension Damper Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

The Key Is Not In The Car Indicator Light IP67 Yellow LED Lamp Beads

The Key Is Not In The Car Indicator Light IP67 Yellow LED Lamp Beads

The key is not in the car symbol indicator light

When the vehicle is started, the dashboard will always light up a lot of small red, green, and green icons, and then all of them will be turned off. In the end, only some basic information such as fuel consumption, mileage, and outside temperature is left.

Many people know that when the other icons are lit, they are performing self-checks, but they may be a little murmured about what functions they represent.

This day, I will introduce you to a symbol indicator. The symbol is shown in the figure. This icon with a key and a question mark represents the key is not in the car. If the key is not in the car icon lights up, you need to pay attention to the following 3 points:

  1. If the key is not in the car lights up, it means that the wireless remote control key has been removed from the car while the engine is running. If the wireless remote control key is no longer in the car, the ignition switch cannot be turned on after the engine is turned off, so the engine cannot be started. In addition, the car cannot be locked from outside the car.
  2. Please put into P gear, otherwise, the car may slip. The door can only be locked in the P position.
  3. If the gearbox is not in the P position when the ignition switch is turned off with the button [START ENGINE STOP], for safety reasons, this driving guide will appear with a warning sound. Please put the gearbox in the P position, otherwise, it will not prevent the car from rolling and cannot be locked.

In May 2019, a customer from Ukraine wanted to buy this the key is not in the car symbol indicator light. Under the introduction of a friend (by the way, this guest’s friend is our old customer) found our Yulin Company. This customer previously purchased the key is not in the car indicator light from another supplier, but the key is not in the car indicator light from another supplier is expensive and has a long construction period.

The indicator light is still the previous model, Is outdated. The most important thing is that another supplier’s goods have quality problems. The customer values ​​quality very much, but the other supplier cannot solve the quality problem, so the Ukrainian customer decided to change the supplier. This time he wanted the key is not in the car indicator with better quality, lower price, and shorter construction period.

Our Yulin company has been carrying out technical updates for many years. The indicator light is the latest design, the latest style, and the price is more advantageous than that of our peers. Our factory can also arrange delivery flexibly.

The Ukrainian customer wanted the largest possible the key is not in the car indicator light. We explained to him that the size of the symbolized indicator light is 8mm, 10mm, 12mm, 14mm, 16mm, The distinction was made in the form of video. The customer liked the 16mm size.

Yulin’s key is not in the car symbol indicator is available in black and silver. Customers carefully compared the differences between the two lamps and preferred the black one.

The customer asked in detail about the voltage and current, wire gauge and wire length, specifications and parameters, and requested to customize the wire gauge and wire length he needed. After Yulin Company inquired about the customer’s needs in detail, he made 10 samples for him.

The customer was very happy after receiving the sample and was satisfied with the quality of Yulin’s indicator light, and then gave our company purchase order.

If you are also interested in Yulin’s indicators and customization capabilities, you can email our staff, and our staff will answer all your doubts.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name The Key Is Not In The Car Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Lane Departure Warning Indicator Light IP67 Red LED Lamp Beads

Lane Departure Warning Indicator Light IP67 Red LED Lamp BeadsWhat does a low lane departure warning mean?

A lane departure warning (LDW) system alerts drivers that their car has inadvertently touched or crossed roadway lane markers at certain speeds. The system will not activate if the turn signals are engaged, because that’s normal behavior before drivers change lanes

How does lane departure warning work?

The departure warning alerts you that your car is about to veer out of the lane and warns you to get back into the lane. That’s the basic idea, but there are several versions of the technology available now, including ones that react and steer away from the lane edge and even proactively keep the car centered.

All forms employ a low-cost camera mounted in the windshield near the rearview mirror that continuously watches the striped and solid lane markings of the road ahead.

It is part of the circle of safety, the three most common and useful driver assists: protecting you to the front (adaptive cruise control and forward-collision warning), side (lane departure warning), and rear side (blind spot detection).

Lane departure warning. This is the original. It is a warning only. When you let the car drift near, onto, or over the lane marking, the car alerts you.

As the driver, you have to take corrective action by steering the car back to the middle of the lane. It doesn’t work if the road has no lane markings. It may not work, or not as well if your state waits until the lane markings are faded before repainting.

Lane marking dots are sometimes harder to track, especially if their coloring has faded. If it’s raining or snowing, the camera may have trouble, too. By design, the system doesn’t alert you if you have your turn signal on, or (some cars) if you apply the brakes.

 

How do I know if my car has a lane departure warning?

The warning on your outside mirror, or on the A-pillar, is for a car in your blind spot. An icon showing two cars side-by-side lights up in the mirror. You get a haptic or audible alert only if your turn signal is on, the opposite of what happens with a lane departure warning

Check the grounding wire on the fuel gauge. To do so, connect the negative jumper cable to the vehicle’s frame and the positive cable to the fuel gauge’s grounding terminal. Turn the ignition to the on position and look at the fuel gauge. If the gauge is not working, then the grounding wire needs to be replaced.

 

How do I turn off the lane departure warning?

To turn off Lane Keep Assist with Departure Warning

If the sensor is green or yellow, or you feel your steering wheel gently guide you back into your lane, the feature is turned on. 3. Press once to turn it off.

 

Where does lane departure warning use?

Lane departure warning most use in the car, but you also can use it in different equipment, like a motorcycle, electromobility, refrigerator, and so on.

What’s the lane departure warning voltage you can do?

Usually we do departure warning ht mean in 12v, but also can do it in 3v,6v,24v 36v 110v 220v 380v.

 

How many colors does lane departure warning have?

Malfunction indicator light can do many kinds of colors, like, red, green, blue, yellow, white.

 

What’s the warranty for Filn lane departure warning mean?

Filn’s lane departure warning with a 5-year warranty. If there is any problem, we accept a return or replacement.

 

What’s the lane departure warning certificate you have?

Lane departure warning approved UL, CE, ROHS, VDE, IP67 etc.

 

How can I buy this lane departure warning?

You can contact them by email at WWW.INDICATORLIGHT.COM, FILN lane departure warning sales email inquiry@cnylin.com.cn, or buy directly from AliExpress and Amazon, though the prices are much better if you buy directly from a factory in China. If you send DHL to the United States, the freight will be about 20 DOLLARS, and the time will take 3 days.

If you want to buy at AliExpress, please click on the AliExpress

 

Does Filn company produce other lane departure warnings?

Yes, Filn company accepts to customize the lane departure warning by your idea, photo, drawing, or words. We are a factory, we have machines to laser different symbols for you, and for our shape, we also can develop a mold for you.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Lane Departure Warning Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Adaptive Lighting IP67 Yellow LED Lamp Beads 12V

Adaptive Lighting IP67 Yellow LED Lamp Beads 12V

Safety is a big selling point for cars. Besides making a solid frame to absorb impact or installing bigger brakes, automakers have been improving car head adaptive lighting to help you see better at night.

Along with brighter bulbs, the head lighting on certain cars can swivel left and right as you go around corners. This will help illuminate the road ahead even as your car turns, so you can still see ahead.

These systems exactly new and original as been around for 40+ years in various forms. However, since computers and electronics are much cheaper and more reliable these days, most new cars have some form of lighting. In most cases, the computer will be able to sense when getting dark outside and will turn the head adaptive lighting on automatically. Head adaptive lighting that can change direction is mostly found on high-end vehicles.

What the adaptive warning lighting means

Depending on the type of adaptive lighting in your car, this warning lighting could mean a few things. Refer to your manual for specific information on your lighting systems.

Head lighting that turns on automatically or those that can adjust brightness use adaptive lighting sensors typically mounted in the windshield. Dirt and debris can prevent these sensors from detecting adaptive lighting properly, so clean the windshield if the system doesn’t seem to be working properly.

The direction changing head lighting use yaw and pitch sensors to determine the position of the vehicle and then adjusts the head adaptive lighting using motors. A malfunctioning sensor or any issues with the functioning of the motor can cause this warning indicator to turn on.

 

With either an lighting system, the adaptive lighting will cause a code to be saved in the memory to help you diagnose the issue. Have the car scanned by a qualified technician and have any necessary repairs performed at the earliest.

Is it safe to drive with the adaptive warning adaptive lighting on?

While adaptive lighting is useful and convenient, it is not essential for you to drive safely at night.

You should always be able to manually turn your head lighting on using the dial. As long as the head adaptive lighting is working, you can continue to use the car normally.

If your adaptive lighting system or head lighting system working properly, our certified technicians can help you by inspecting and diagnosing it.

Next Step

Schedule Head adaptive lighting is not working Inspection

The most popular service booked by readers of this article is Head lighting is not working Inspection. Once the problem has been diagnosed, you will be provided with an upfront quote for the recommended fix and receive $20.00 off as a credit towards the repair.

Your Mechanic’s technicians bring the dealership to you by performing this job at your home or office 7-days a week between 7 AM-9 PM. We currently cover over 2,000 cities and have 100k+ 5-star reviews…

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Adaptive Lighting
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Air Suspension Warning Indicator Light IP67 Red LED Lamp Beads

Air Suspension Warning Indicator Light IP67 Red LED Lamp Beads

Air suspension warning indicator light is available in five regular colors: red, yellow, blue, green, and white. If customers need special colors, we can also customize them.

The quality of the Air suspension warning indicator light depends largely on its chip, just like the human heart. A good chip can make the life of the Air suspension warning indicator light longer. The Air suspension warning indicator light will also be brighter. When installing the indicator light, please don’t worry about wiring errors, because it is a non-polar chip. There are no positive and negative electrodes.

Air suspension warning indicator light service life: If the chip is the heart of the air suspension warning indicator light, I feel that the lamp bead is the liver.

The lamp beads of this indicator light are made of high-grade neon bulbs, with a service life of 10 years to 50,000 hours, very high-pressure resistance, and the light source is also very shiny.

But customers can also choose to use neon bulbs and LED bulbs. Air suspension warning indicator light waterproof rating: The waterproof rating of the indicator light is IP66 by default. If the customer has requirements for the waterproof level, the waterproof level can be IP68.

The indicator light shell material: The indicator light shell material is PA66 nylon. Because of its high mechanical strength, fatigue resistance, high-temperature resistance, smooth surface, wear resistance, and other advantages. The indicator light is exquisitely designed.

Usually, the head of the flat-head indicator light is very flat, but the disadvantage is that the light source emitted is not flat. However, through the innovation of our company’s R&D personnel, the head of the indicator light has been modified into a honeycomb shape. Protruding.

The indicator light voltage of food machinery can be 3V 6V 12V 24V 110V 220V 380V and so on.

The warranty period of the FILM LED indicator is 5 years. If FILN Air suspension warning indicator light has quality problems or damage during its use within 5 years, FILN company promises to replace the indicator light free of charge.

Certificate certification: FILN LED indicator factory has obtained many international certifications, including UL certification in the United States, VED certification in Germany, CE certification in the European Union, ROSH certification, etc., and it has also obtained ISO90001 quality management system certification.

Is the indicator light only monochrome? Red yellow blue green white?

The two colors are red/green blue/yellow-green/blue white/red.

The colors are red/blue/green, white/yellow/green.

How to distinguish whether the Air suspension warning indicator light is good?

  1. Whether the materials (especially LED) and resistance of the Air suspension warning indicator light are used properly. If the quality and resistance of the Air suspension warning indicator light are not good, the Air suspension warning indicator light will be bad. When designing the indicator light, it will test the withstand voltage of the indicator light. The performance of temperature, life, method, and other aspects ensure the stability of the index quality.
  2. Whether the production process of the Air suspension warning indicator light is consistent depends on the experience and professional level of the Air suspension warning indicator light factory. When the conventional Air suspension warning indicator light factory produces the new Air suspension warning indicator light, it will first make a process flow chart and display the lighting process card, indicator light work instructions, and indicator light inspection.

How to buy Air suspension warning indicator light?

You can click on the link below to purchase and learn about other products of our company.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Air Suspension Warning Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Steering Lock Alarm Indicator Light IP67 Imported LED Lamp Beads Red

Steering Lock Alarm Indicator Light IP67 Imported LED Lamp Beads Red

1. What is the steering lock alarm indicator light?

The steering lock alarm indicator light is also the car steering wheel lock indicator light. The steering wheel lock is an effective anti-theft tool for the car.

The steering wheel lock is generally composed of a lock handle, a locking base, and a lock rod. The lock base and the lock shell are directly installed on the lock handle. One end of the lock handle is directly provided with a lock rod. There is a series of platforms on the lock rod.

The side is vertical and the other side is the hypotenuse. When using, lock the fork and hook of the steering wheel first, and clamp it on the rim of the steering wheel of the car, thereby restricting the rotation of the steering wheel, thereby achieving the anti-theft effect. The steering lock alarm indicator light is to remind the user of such an existence.

 

2. What is the function of the steering lock alarm indicator light?

A steering lock alarm indicator light with an alarm includes a lock having a lock core with a chamber containing an alarm and at least one light hole. The alarm consists of a circuit board, a battery, a buzzer, and a touch switch. The circuit board capable of sending signals has a warning light and a high-density LED light.

Also, a help-signaling device is installed at a conspicuous location of a car and provided with at least one lamp panel. Each lamp panel is provided with a wireless receiver for receiving signals from the alarm and formed of luminescent lamps or LED lamps to show help signals.

So, should the buzzer be moved by a burglar, it would sound immediately, spontaneously activating the high-density LED light to radiate toward the driver’s seat and the lamp panel lit, achieving multiple anti-theft effects.

 

3. Why does the power steering alarm indicator light turn on when unlocking?

It will be on, and it will be off after startup. If it is not off, there is a problem with the booster system. When the key is opened, the steering lock alarm indicator light will be on, and it will automatically go out after the computer detects that there is no fault code. Some cars need to be started for a few seconds before being turned off. If it does not go off during driving, it means there is a fault and needs to be repaired.

 

4. The car dashboard indicator shows a car locked icon, the car can’t be sent, and other buttons or instructions are invalid. Why?

That is the steering lock alarm indicator light. The car dashboard indicator shows a car locked icon. The car cannot be sent because the car’s anti-theft system has not received a legal unlock key signal.

The gateway locks the engine control system. Even if the door can be opened, the car cannot be started normally. Maybe the key chip is lost and needs to be re-matched, or the anti-theft system malfunctions. If the anti-theft system is activated, you need to go to the 4s store to re-pair the keys and eliminate it.

This is just a small part of the steering lock alarm indicator light. If you want to know more about the steering lock alarm indicator light, pls contact:sales5@filn.com.cn

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Steering Lock Alarm Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Low Key Battery Indicator Light IP67 Imported LED Lamp Beads Yellow

Low Key Battery Indicator Light IP67 Imported LED Lamp Beads Yellow

What does low key battery mean?

What the key fob battery low warning light means. When the key is in use, the computer monitors the output voltage of the fob’s battery. Once the voltage gets to a certain point, the warning light will illuminate on the dash to let you know to replace the batteries. … Make sure that you use the correct type of battery.

How do you know if your key battery is low?

As the battery wears out, however, the range and signal strength of the fob transmitter will be reduced. If you notice that your key remote does not unlock your car, lock your car, or start the engine for those with the automatic start button as early as it should, it’s probably time to replace the battery. At this point, the Low key battery indicator light will remind you to replace the battery.

How much voltage does this 4-wheel drive?

We have 3 volts, 12 volts, 24 volts, 30 volts, 120 volts, 240v, and 360 volts. We can do anything from 3 volts to 300 volts. But our 240V indicator is the most popular among customers, and many regular customers will place orders for the 240V indicator every month

Can a low battery in the key fob cause the car not to start?

If nothing happens, it may mean one of several things: The battery inside your key fob is dead or too low to send a good signal to the keyless entry system and needs to be replaced. … Your car battery is extremely low or dead. This may require a jump start before your engine will crank and start. You need to replace the battery when the light comes on

Do I need to reprogram the key fob after changing the battery?

Key fobs are a wonderful way of being able to access your vehicle from far away. However, like anything else that is battery operated, the battery often has to be changed. Do you have to reprogram the key fob after changing the battery? Usually, you do not need to reprogram the key fob.

What color does the low key battery indicator light have?

Our pilot lights come in a variety of colors, such as red, yellow, green, blue, white… The red 4wd indicator light is still the most popular and sells best. Therefore, our main product is also red 4wd indicator light.

What is the difference between low key battery indicator light housing?

The housing has plastic and metal indicator lights, such as it is the same size of 10 mm and the product parameters are the same. We have both metal and plastic. And we also have two kinds of tape and pin. General customers will confirm before the next inquiry to bring the line of pins and plastic or metal.

How do we buy low key battery indicator lights?

You can contact us directly, you need to fill in some of your information below, we will contact you directly after receiving the email. After the communication, we will carry out the production. If you don’t know what products do we have, you also can visit our official website www.indicatorlight.com to know more information about the details.

How can I buy low key battery indicator light?

You can contact them by email at WWW.INDICATORLIGHT.COM, FILN CAR INDICATOR LIGHT sales email inquiry@cnylin.com.cn, or buy directly from AliExpress and Amazon, though the prices are much better if you buy directly from a factory in China. And If you send DHL to the United States, the freight will be about 20 DOLLARS, and the time will take 3 days.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Low Key Battery
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Information Indicator Light IP67 Imported LED Lamp Beads 16MM

Information Indicator Light IP67 Imported LED Lamp Beads 16MM

What is Information indicator light means?

The indicator light generally refers to a lamp that transmits information and is generally used in road traffic, automobiles, construction, and other places. Information indicator lights are in different places, the information that the information indicator light conveys is different; the information that the information indicator light conveys and what kind of light is used to transmit it has a certain The normative is a familiar habit in people’s lives.

Now the indicator light generally uses LED material as the light source, which can reach the energy-saving and environmental protection level.

 

Where does the Information indicator light show our daily life?

Usually, in our daily life, and In-car dashboard is normal common.

 

Where is the Information indicator light used in the car?

The indicator lights are mainly direction lights, tail lights, and brake lights on the outside of the car; inside the car are mainly the lighting and display of various instruments. Compared with traditional incandescent lamps, ultra-high-brightness LEDs used in automotive indicator lamps have many advantages and have a broad market in the automotive industry.

 

How does Information indicator light work?

There are a few simple components inside the thermal scintillator: an electrical contact that conducts current to a wire.
A slightly bent spring steel sheet connected to electrical contact. A resistance wire wrapped around a small spring steel sheet. When the thermal scintillator pulls down the  Information indicator light rod, the thermal scintillator is connected to the turn signal bulb through the  Information indicator light switch. This way the entire circuit will be connected and current can flow in the circuit. At first, the spring steel sheet did not touch the contacts, so only the resistor had a current. Electric current flows through the resistance wire to heat the small spring steel sheet, and then transfers the heat to the  Information indicator light.

 

Where can customers buy Information indicator lights?

You can search Filn company to buy the Information indicator light.

 

Can customers buy the sample from Filn company?

Yes you can buy samples,Filn company is a manufacture, and we can provide the sample to the customers also very fast.

 

Can customers customize the Information indicator light?

Yes, Our company welcomes customized products and services, for different colors of Information indicator light and different logos, colors.

 

How many volts is the Information indicator light?

Generally, the voltage of the indicator light is 12V, but according to your needs, we can provide you with the volts of the alternator indicator light you need.

 

How can you order an Information indicator light from us?

You can contact us via email and our email id is sales email inquiry@cnylin.com.cn, or directly from AliExpress, and please click on the AliExpress.

If you are urgent to receive them, we can send fast Express to you, like DHL.

 

How long does the Information indicator guarantee?

If you buy high beam indicator light, FILN promises to replace it for free within 5 years.

 

You can leave us a message directly at the bottom of the page.

You can also choose to search FILN directly on Alibaba. Then contact us.

After receiving your order for the indicator, we will proceed to production.

We have many other products. If you want to know more about indicators, you can also visit our official website www.indicatorlight.com. Any question and the problem just feel free to contact us.

Our sales email is inquiry@cnylin.com.cn

Contact us now!!!

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Information Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Steering Assistant System Malfunction Warning Light For Power Assist System

Steering Assistant System Malfunction Warning Light For Power Assist System

Some symbols on your car’s dashboard are more obvious than others. However, it’s important to know exactly what they mean in case you need to pull over and call for help. At Virginia Tire & Auto, your safety is our No. 1 priority. That’s why we’re breaking down your dashboard, symbol by symbol.

What it looks like: Pyramid on the dollar bill … or is that what the Illuminati want you to think it looks like?

What it means: There is an issue with your anti-skid system, and it may be shut off completely.

Under ordinary circumstances, turning your Steering assistant system malfunction wheel shouldn’t cause any unusual noise. It should simply direct your car in the direction you want to go to. However, there are many parts that are affected by physical stress during turns, and if you’re hearing a creaking noise when turning, or a whining sound, a groaning, or any other unusual noise, it could be a sign of something serious.

 

How this system works:

Your car’s Steering assistant system malfunctions and the suspension system is very complex, and it’s all interconnected in one way or another. Turning your Steering assistant system malfunction wheel engages the power steering assistant system malfunction rack, which requires the pump and belt to be in good condition, and that there is plenty of fluid in the system. It also affects the suspension – your struts take additional stress while turning.

 

In addition, you also have to consider the stress and strain placed on ball joints used to connect the front steering assistant system malfunction and suspension components (Steering assistant system malfunction knuckle, control arms, etc.).

 

All of these components must be able to support the weight of your vehicle while being free to move in different ways. The need for movement means there needs to be plenty of lubrication, and it also means the potential for wear and tears on a number of different parts (all of which are limited lifetime components that will need to be replaced at some point in the life of your car).

 

Common reasons for this to happen:

Worn Shocks/Struts: Your shocks and struts are most likely the gas-filled type. They’re good at what they do, but they do wear out. If you’ve noticed fluid on the side of one of your front shocks, chances are good that it’s blown and needs to be replaced. You may also notice that your car feels very loose and bouncy when going over bumps or through turns.

 

Dry Jounce Bushing: The jounce bushing is located at the top of the front strut. If it’s dry, it can cause a groaning/creaking sound during turns. If not repaired, this problem can become more serious.

 

Dry/Damaged Suspension Bushings: Bushings wear out over time. Eventually, they crack, deteriorate, and must be replaced. It’s possible that this is causing the creaking while turning the Steering assistant system malfunction wheel.

 

Worn Ball Joints: Ball joints allow control arms and Steering assistant system malfunction knuckles to adjust to movement. They must be well lubricated in order to do their job, but the grease can wear out over time. When this occurs, expect to experience noise and deterioration.

 

Damaged Tie Rod Ends: Tie rods connect your Steering assistant system malfunction system to help move the wheels when you turn your Steering assistant system malfunction wheel. Creaking while turning can be a sign of damaged tie rods, but it’s more usual to hear a knocking sound when making tight, low-speed turns.

 

Damaged Power Steering assistant system malfunction Pump/Rack/Belt: Usually, problems with the power steering assistant system malfunction rack, pump, or belt cause a whining sound, more noticeable during low speed turns. However, that can be mistaken for a creaking sound.

 

What to expect:

A top-rated mobile mechanic will come to your home or office to inspect your car’s Steering assistant system malfunction and suspension system in order to diagnose the creaking noise you’re experiencing. The mechanic will then provide a detailed inspection report that includes the scope and cost of the necessary repairs.

 

How it’s done:

The mechanic will inspect your Steering assistant system malfunction and suspension system, including the power steering assistant system malfunction rack, pump and belt, tie rods, ball joints, and more. It may be necessary for the mechanic to test drive the car to verify the complaint and pinpoint the origin of the sound.

 

How important is this service?

A creaking sound when turning your Steering assistant system malfunction wheel may be nothing more than a sign that your suspension system needs lubrication, but it may be a sign of something more serious, including tie rod damage, power steering assistant system malfunction rack damage, or a failing strut/shock. One of our professional mechanics can inspect your vehicle, determine the underlying cause, and then repair your car.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Warning Light For Power Assist System
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Left And Right Turn Lights Imported LED Lamp Beads IP67

Left And Right Turn Lights Imported LED Lamp Beads IP67

What are Left and right turn lights?

Left and right turn lights are a pair of intermittent flashing indicator lights that flash in unison to warn other drivers that the vehicle is a temporary obstruction. They are also called hazard flashers and hazard lights. Different countries use hazard warning lights in different ways. In New Zealand, we wouldn’t use them on a freeway to warn other drivers that we’re slowing down, but in the UK this is recommended.

They are usually activated by pressing a button on the dashboard that looks like a red triangle, as shown. Some vehicles (usually European ones) will automatically activate the hazard warning lights under heavy braking or if the vehicle is involved in an accident.

Hazard warning light button

When should you use Left and right turn lights?

They are to warn other road users that you are a temporary hazard. For example, if you have broken down on the side of the road, or you are changing a tire. If you are being towed, you should use your hazard warning lights.

If you are being towed, and you are using your hazard lights, you will need to use hand signals to indicate direction because the hazard lights override the indicators.

When shouldn’t you use the lights?

They shouldn’t be used if you are driving in traffic. You should not use them to warn other drivers if you parked illegally (you shouldn’t be parking illegally). If your hazard warning lights are left on while you are driving, any signaling with your indicators will not be able to be seen.

 

When should you not use the lights?

Left and right turn lights use are not permitted while driving except for emergency vehicles, stopped or slowed vehicles to indicate a traffic hazard, when traveling as part of a funeral procession, or traveling slower than 30 mph.

 

Should you use Left and right turn lights in heavy rain?

Left and right turn lights can actually reduce visibility making other drivers think you are stopped or stalled. … They make it difficult to see if motorists ahead are tapping on the brakes, and they don’t allow you to use your turn signals.

 

How long can I leave the Left and right turn lights on?

The time varies from overnight to an hour or less depending on the vehicle and the condition of the battery. In modern cars with LED lights, the warning lights should be able to run for many hours without discharging the battery to the point where it won’t crank the engine over.

 

What’s the Left and right turn lights can do?

Usually we do the lights in 12v, but also can do it in 3v,6v,24v 36v 110v 220v 380v.

 

How many colors do Left and right turn lights have?

Left and right turn lights can do many kinds of color, like, red, green, blue, yellow, white.

 

What’s the warranty for Left and right turn lights?

Filn’s Left and right turn lights with a 5-year warranty. if there is any problem, we accept a return or replace.

 

What’s the Left and right turn lights certificate you have?

Left and right turn lights approved UL, CE, ROHS, VDE, IP67, etc.

 

How can I buy these Left and right turn lights?

You can contact them by email at WWW.INDICATORLIGHT.COM, FILN CAR INDICATOR LIGHT sales email inquiry@cnylin.com.cn, or buy directly from AliExpress and Amazon, though the prices are much better if you buy directly from a factory in China. If you send DHL to the United States, the freight will be about 20 DOLLARS, and the time will take 3 days.

If you want to buy at AliExpress, please click on the AliExpress

 

Does Filn company produce other Left and right turn lights?

Yes, Filn company accepts the customize of the Left and right turn lights by your idea, photo, drawing, or words. We are a factory, we have machines to laser different symbols for you, and for our shape, we also can develop a mold for you.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Left And Right Turn Lights
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Car Engine Indicator Light LED Lamp Beads Cruise Control Indicator Light

Car Engine Indicator Light LED Lamp Beads Cruise Control Indicator Light

The working principle of the car engine indicator light?

Usually, the relationship between vehicle speed and throttle opening when the car is running on a flat road is stored in the ROM of the cruise control system ECU. The cruise control system automatically maintains the car at a constant speed according to the target speed.

When the car is cruising at a constant speed when the car speed drops, the ECU increases the throttle opening to increase the engine power and torque, and the car speed reaches the set speed. Conversely, reduce the throttle opening.

When the vehicle speed is below 40 km/h and above 160 km/h, the cruise system does not work. Of course, the upper and lower limits are slightly different depending on the model.

If the control line is made to be in a vertical state, the speed fluctuation (control error) is reduced to zero. In this way, small changes in driving resistance will cause changes in the throttle opening. Due to the excessive sensitivity of the response, it is easy to cause running. Therefore, it is necessary to comprehensively consider the control error and the problem of traveling, and select the appropriate control line slope.

Once the sensor of the system fails, or the control signal circuit is cut off because there is no vehicle speed signal, the low-speed limit circuit will consider the vehicle speed to be zero and stop the cruise control system.

What color can the car engine indicator light be?

Car engine indicator light There are five regular colors of red, yellow, blue, green, and white. If customers need special colors, we can also customize them.

What voltes can the car engine indicator light be?

Indicator light the voltage can be 3V 6V 12V 24V 110V 220V 380V and so on.

Indicator lights the warranty period of the indicator lamp is 5 years. If FILN Car engine indicator light has quality problems or damage during its use within 5 years, FILN company promises to replace Car engine indicator light free of charge.

What certification does Car engine indicator light have?

FILN LED engine indicator light has obtained many international certifications, including UL certification in the United States, VED certification in Germany, CE certification in the European Union, ROSH certification, etc., and it has also obtained ISO9001 quality management system certification.

How to distinguish a good car engine indicator light?

  1. Whether the material of the car engine indicator light (especially LED) and resistance are used properly, if the quality and resistance of the car engine indicator light are not good, the car engine indicator light will be bad. When designing the indicator light, it will test the withstand voltage of the indicator light. The performance of temperature, life, method, and other aspects ensure the stability of the index quality.
  2. Whether the production process of car engine indicator light is consistent depends on the experience and professional level of the car engine indicator light factory. When the conventional car engine indicator light factory produces a new car engine indicator light, it will first make a process flow chart and display the lighting process card, indicator light work instructions, and indicator light inspection.

How to buy this car engine indicator light?

You can click on the car engine indicator light purchase link to buy directly.

https://www.indicatorlight.com/engine-temperature-warning-light/

Or you are interested in our other products. You can click on this link,

https://www.indicatorlight.com/

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Cruise Control Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Key Indicator Light High Quality LED Lamp Beads Press The Clutch Pedal

Key Indicator Light High Quality LED Lamp Beads Press The Clutch Pedal

Key Indicator Light

In-car function keys: including ESP switch key, central control lock key, reversing radar key, headlight cleaning key, rear sunshade key and fuel tank opening key, etc. Many people already know cars well, but they don’t know the buttons, knobs, and signs inside cars.

The light control is usually in two positions, the left side panel of the steering wheel and the left side lever, and most European cars are on the panel, Japanese and Korean cars are mostly on the lever.

The function of audio control is similar, we introduce some of the more common function keys. Due to the introduction of touch screens, many physical buttons responsible for audio control functions have now disappeared.

The manual air conditioner is relatively simple, and the operation is relatively simple, mainly to control the wind speed, temperature, and air outlet mode.

The power seat adjustment is actually very simple, just adjust the buttons in different positions according to the shape of the seat.

 

1. What is the function of the key indicator light, and why does it light up?

The key indicator light that there is a security error code. When the vehicle control module sees that the ignition switch is not turned on with the key programmed by the vehicle, or there is an error in the safety protocol of the vehicle safety system, this light is on.

Common reasons why this happens:

(1)Key failure

(2)Keychain battery

(3)Key antenna failure

(4)Control module failure

(5)Electrical interference

 

2. Can I drive with the key indicator light on? (Can I drive in fail safe mode?)

In most cases, the vehicle will not start when the key indicator light is illuminated. It will have to be towed to a repair facility capable of programming and servicing the security system of your specific vehicle.

 

3. How to fix the key indicator light?

  • Replace the key fob battery
  • If the problem persists, you will have to tow the vehicle to a repair facility that can repair the vehicle’s safety system.
  • Another option is to let the mobile key programmer come to you to repair the car.

If the key start function fails, the key indicator light flashes. In this case, the engine may start, you need a professional to deal with.

 

4. What volts can the key indicator light do?

Normally, it can be 3V~380V. Of course, it depends on where the key indicator light is applied. Different currents are matched with different voltages. Under safe circumstances, you can tell us your requirements. Our customized service will definitely satisfy you.

 

If you want to buy more type indicator light, pls contact us:sales5@filn.com.cn

This is our official website:www.indicatorlight.com.

This is Alibaba URL:https://filn.en.alibaba.com/

AliExpress URL:https://filn.aliexpress.com.

You can select and purchase through the official website, Alibaba, and AliExpress.

Recently we open an account on Facebook, YouTube, TikTok, LinkedIn, Twitter, this is the link to our Facebook account, https://www.facebook.com/cnfiln/etc,this kind of social software, can let customers easier to find the products. At the same time about the freight, we will help you to choose the best way, such as in the regulation of price can buy multiple goods, find to one of the most thoughtful services for the customer.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Press The Clutch Pedal Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

4WD Indicator Light Downhill Control Indicator Light High Quality LED Lamp Beads

4WD Indicator Light Downhill Control Indicator Light High Quality LED Lamp Beads

Why 4wd indicator light?

A lot of the time, a flashing 4WD light is no reason to be alarmed, because it simply means that the system is working as designed. On vehicles where four-wheel drive is only activated on-demand — that is to say when traction conditions require it — this light shows up to tell you that it’s been activated

What does it mean when your 4wd light comes on?

The 4WD switch light will indicate 2WD or Auto when drive engaged. … The “Service 4WD System” message does not mean routine maintenance of the 4WD system is required. The “Service 4WD System” message indicates a problem with the 4WD system that should be properly diagnosed and repaired.

How do I know if my 4 wheel drive actuator is bad?

Symptoms of a Bad or Failing Front Axle Engagement Switch

1. Difficulty engaging four-wheel drive. One of the first symptoms of a potential problem with the front axle engagement switch is difficulty engaging the vehicle’s four-wheel-drive system. …

2. Four-wheel drive becomes stuck. …

3. Four-wheel drive mode does not activate.

So you have to have 4wd indicator light on your car

How do I unlock my 4-wheel drive?

In 4wd turn, the front wheels (left or/and right) while driving in a tight circle (1 or 2 mph) and you should feel them bind up if 4wd is working. Find a steep gravel driveway or road drive up to it in 2wd stop try to go then pull into 4wd you should pull out without spinning if it engages. The indicator light is used to warn the driver of a problem.

How much voltage does this 4-wheel drive?

We have 3 volts, 12 volts, 24 volts, 30 volts, 120 volts, 240v, and 360 volts. We can do anything from 3 volts to 300 volts. But our 240V indicator is the most popular among customers, and many regular customers will place orders for the 240V indicator every month

Except for the different voltages, is there any current?

There are several types of current, 1A,2A,3Aand 30A, but the current has little effect on the function of the indicator light. The main difference is voltage and material

What color does the 4wd indicator light have?

Our pilot lights come in a variety of colors, such as red, yellow, green, blue, white… The red 4wd indicator light is still the most popular and sells best. Therefore, our main product is also red 4wd indicator light.

What is the difference between 4wd indicator light housing?

The housing has plastic and metal indicator lights, such as it is the same size of 10 mm and the product parameters are the same. We have both metal and plastic. And we also have two kinds of tape and pin. General customers will confirm before the next inquiry to bring the line of pins and plastic or metal.

How do we buy 4wd indicator light?

You can contact us directly, you need to fill in some of your information below, we will contact you directly after receiving the email. After the communication, we will carry out the production. If you don’t know what products do we have, you also can visit our official website www.indicatorlight.com to know more information about the details.

How can I buy 4wd indicator light?

You can contact them by email at WWW.INDICATORLIGHT.COM, FILN CAR INDICATOR LIGHT sales email inquiry@cnylin.com.cn, or buy directly from AliExpress and Amazon, though the prices are much better if you buy directly from a factory in China. If you send DHL to the United States, the freight will be about 20 DOLLARS, and the time will take 3 days.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Downhill Control Indicator Light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Vehicle indicator lights LED IP67 Speed Limit indicator light

Vehicle indicator lights LED IP67 Speed Limit indicator light

Vehicle indicator lights 12v 110v red

The vehicle indicator lights can monitor the vehicle status in real-time, and it can tell you the most intuitive and accurate function status of the vehicle, warning prompts, fault repairs, etc. Yulin’s No. 224 symbol represents the speed limit. So why is the speed limiter symbol on the car dashboard lit? In layman’s terms, there is a problem with the speed sensor. You should go to the service station to check it. Generally, delete the code first, and then determine if the sensor is broken. If there is a problem with the system or sensor, this needs to be detected with a dedicated computer. It is recommended to check in the store as soon as possible and deal with it free of charge during the warranty period. Generally, car indicator lights have 4 colors: green, blue, yellow, and red. Different colors have different meanings.

Green/blue indicator light: generally indicates the status of vehicle functions, indicating that the function is on or off;

Yellow indicator light: Generally, it indicates a warning that there is a problem with a certain function or accessory of the vehicle, which requires the owner’s attention and repairs at an appropriate time;

Red indicator light: Generally, it is a serious warning. The vehicle has a serious failure or is in a dangerous state. It is necessary to stop driving immediately, clear the fault and repair it immediately;

The speed limit symbol vehicle indicator light is a fault indicator, and its color is generally yellow.

What size lamp can Yulin’s symbol vehicle indicator lights make?

Yulin’s symbol vehicle indicator lights can generally be 8 mm, 10 mm, 12 mm, 14 mm, 16 mm, etc. Our indicator lights are available in black and silver. At the same time, they are divided into cable and pin types. You can choose black with line or pin, or silver with line or pin.

How long is the delivery time of Yulin’s vehicle indicator lights?

If you need less than 100, it can be done in 2~3 days. If you need a few hundred looks, usually 8~10 days can be completed. If you need thousands or tens of thousands, you need to communicate with our production department in advance and give a specific delivery date.

What is the use time limit of the vehicle indicator lights?

The quality of our vehicle indicator lights are very strict, and the life of the indicator light can reach 80,000 hours under normal use.

If you are interested in Yulin’s vehicle indicator lights, you can go to the websites of Alibaba or AliExpress to buy, or email our staff: inquiry@cnylin.com.cn

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Speed Limit indicator light
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

Check Engine Indicator Light Meaning Replace Oil-Water Separator

Check Engine Indicator Light Meaning Replace Oil-Water Separator

Check engine indicator light meaning 24v pilot light

Yulin’s indicator lights can be customized with various symbols, this symbol represents the replacement of the oil-water separator.

The main function of the oil-water separator is to remove the moisture and impurities in the diesel, to reduce the failure of the fuel injection nozzle, thereby extending the service life of the engine. Because even the best diesel will contain moisture and impurities, problems with the oil-water separator may cause the engine to accelerate unstable and weak, emit black smoke, carbon deposits, and engine white smoke. Equipped with an oil-water separator can prevent the abrasion of the fuel injection nozzle, to achieve stable engine operation and increase life. Therefore, the symbol indicator for replacing the oil-water separator is very important, and Yulin’s symbol indicator can achieve very good quality.

What will the Yulin check engine indicator light mean symbol indicator to be used for?

Yulin’s check engine indicator light meaning symbol indicator can be used in many ways, such as car dashboards, electric bicycles, and coffee machines. Air purifiers and so on. In addition to the car dashboard, you can also customize other symbols, specific symbols

How much voltage can Yulin’s check engine indicator light meaning indicator light do?

Our check engine indicator light meaning indicator lights can be made of lower voltage lamps such as 3v, 9v, 12v, 36v, and high voltage lamps such as 110v, 220v, 380v, etc. Usually, the most commonly used voltage for customers is 12v. The voltage range of our check engine indicator light meaning indicator light is 3v~380v.

How many light colors are available for Yulin’s symbol indicator?

Yulin’s symbol indicator generally has five colors, red, yellow, blue, green, and white. If the customer wants to customize the car symbol indicator light, different colors represent different degrees of car failure, so it is recommended that the customer customize the color of the check engine indicator light meaning indicator light according to their own situation.

What is the warranty period of Yulin check engine indicator light meaning indicator lights?

Normally, the warranty period of our check engine indicator light meaning indicator lights is 1 year.

How to buy Yulin’s symbol indicator?

You can email inquiry@cnylin.com.cn directly, or go to ALIBABA or AliExpress to purchase directly. We also have our stores on these two platforms, and there will be certain promotions, such as coupons, full reduction activities, etc.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name Replace Oil-Water Separator
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃

BMW Dash Indicator Light Symbols ESP System Failure IP67

BMW Dash Indicator Light Symbols ESP System Failure IP67

BMW dash indicator light symbols 110v pilot lamp

This car icon is called the ESP system failure icon, and ESP is the body stability system. When the ESP fault light is on, it means that the car’s electronic stability system is malfunctioning. The ESP system is generally composed of sensors, actuators, and control units. Since the ESP system generally shares a sensor with other electronic devices, the ESP may also be lit. Caused by the influence of other components.

If the ESP fault light is on while driving, we must reduce the speed, try to avoid turning at a large angle, and find a repair shop in time. As mentioned above, the ESP system may share sensors with many devices, so when the ESP light is on abnormally, it must be checked and repaired in time to avoid serious disasters.

Yulin Company produces a BMW dash indicator light symbols, which is actually a BMW dash indicator light symbols. Such a sign of vehicle slippage needs to be engraved on the surface of the head. There are usually five colors of BMW dash indicator light symbols, red, yellow, blue, green, and white. However, the colors of the car bmw dash indicator light symbols are usually divided into three types. The red represents the hazard bmw dash indicator light symbols, which means that if it is not processed, it may cause serious injury. The yellow bmw dash indicator light symbols is a fault bmw dash indicator light symbols. When this type of bmw dash indicator light symbols is on, it means that a certain function of the car has been lost and needs to be overhauled. The green is a reminder light to remind you that certain functions can be used. The vehicle stability system fault light is a fault indicator, so in general, yellow or orange is enough.

Yulin’s bmw dash indicator light symbols can be made into a wire type or a pin type. The length of the conventional line with the line is 20 cm, and the length of the exposed line is about 185 mm. The cable length can be customized. If you need a longer cable or a shorter cable, Yulin can meet your requirements.

The minimum voltage of the bmw dash indicator light symbols produced by our company can be 3v, and the maximum can reach 380v. The voltages that customers buy more are 12v, 24, 110v, 220v, and so on. The color of the bmw dash indicator light symbols can be selected from five colors of red, yellow, blue, green and white. Two-color and three-color are also available. The head shape of the indicator light has a flat-convex head and a concave head, and the application range of the flat head is more extensive.

Yulin has its own production plant and has been carrying out technological innovation for many years, which has effectively reduced the production cost, so the price is also very favorable. The construction period is also very flexible and convenient.

If you are interested in Yulin’s bmw dash indicator light symbols, email our staff immediately to ask for more detailed information.

Other car symbol indicator

Brand-New Introduction Of 64 Dashboard Indicator Light

Click to view the video introduction of dashboard indicator light

Symbolic name ESP System Failure
Panel Mount Diameter 8 mm, 10 mm, 12 mm, 14 mm, 16 mm
Contact Way With wire
Install Way screw terminal
Lamp Type LED
Rated voltage AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color red yellow blue green white
Product Design convex head
Shell Material brass plated nickel/stainless steel
Base Material PA66 nylon
Terminal Material brass
Applications Coffee machine, kitchen equipment, household appliances,    automobiles, medical equipment, industrial equipment, etc
Component name material
lens PC plastic
Metal body H59 brass or 204 stainless steel
wahser T10 Cold Rolled Steel
rubber ring SIL silica gel
nut H59 nickel plated brass
housing PA66 nylon
Light source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
plug-in C2680 RoHS brass
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃