Search

8MM 12V 4 Pin Momentary Mini LED Push Button Switch

FLM8-10EJ

 

  • The mounting hole size of the product is 8mm, except the size of the product, we also have 10mm, 12mm, 16mm 19mm, 22mm, 25mm, 28mm, 30mm, 40mm etc., the size is complete.

Mini LED push button switch parameters

Production Series FLM8-10EJ Light guide button PC plastic
Button Shape round actuator 304 Stainless steel
Button LED Color Red, blue, green, yellow and white Housing sleeve H59 nickel plated brass
Mechanical Life The 300 thousand time Button pin H62 Copper alloy
Electrical Life The 100 thousand time rubber ring SIL silica gel
Protection Level IP65 IK09 nut H59 nickel plated brass
Rated Voltage 36V DC housing PA66+GF20% nylon
Rated Current 1A Light source LED
Rated Power 36W Resistor Metal film
Operating Temperature -25℃~+85℃ contact AgCdO12

The following is the description of the mini LED push button switch.

  • The head shape of the 8mm mini LED push button switch is high flat head, which is suitable for high flat head buttons due to the small size of 8mm.
  • The product has three materials, such as brass, stainless steel, zinc alloy. Brass product’s cost is relatively low, and stainless steel is corrosion-resistant, while the appearance of the zinc alloy can be plated in a variety of different colors.We are also working on 22mm plastic material, which can reduce the corresponding costs with constant quality. The plastic material of the mini LED push button switch is PC and PA66, which high-temperature resistance is 160 degrees.It is usually used between minus 40 degrees and 80 degrees. This one shown on the picture is usually made of brass material.
push button switch material
  • The product can achieve five colors, such as red, yellow, blue, green, white. At present, we can only produce the product that is monochrome, 4 pins, 1NO function. The current of the mini LED push button switch is 1A/ 250V AC.
  • The product has a variety of voltages, such as 3V, 6V, 12V, 24V, 110V, 220V, etc., we can produce other voltages like 48V. The mechanical life of the mini LED push button switch is 50,000 times. The product had passed the certifications of CE, ROSH, etc..
Multiple button voltages

What is the mini LED push button switch?

The mini LED push button switch is a switch that uses push button to push the drive mechanism, which make the movable contact and the static contact press or disconnect and realize the circuit’s switching.

How does the mini 12V led push button switch work?

The mini LED push button switch is a manually controlled master ordering appliance. It is mainly used to issue operation commands, turn on or off the control circuit, and control the operation of mechanical and electrical equipment.

The operation principle of the push button is pretty simple.

For normally open contacts, the circuit is disconnected before the button is pressed, when the push button is pressed, the normally open contact is connected and the circuit is switched on.

For normally closed contacts, the contact is closed before the push button is pressed, when the push button is pressed, the contact is disconnected and the circuit is disconnected.

A button can also have multiple pairs of simultaneous contacts due to the control circuit operation.

How to connect the wire with the mini led push button switch?

The most conventional wiring requirements are: the light of the switch locked is on, the device starts.

The light of the switch reset is off, the device is closed.

The wiring mode is as follows: the first step is that the positive pole of the power source is connected to the switch’s load pin, the other load pin is connected to the LED pin (+) and the positive pole of the device.

The second step is that the negative pole of the power source is connected to the LED pin (-) . As the following picture shows.

Button switch wiring

Another requirement is that the switch locks, the device starts. Switch reset, the device is closed and the lamp is on.

The wiring mode is as follows: the first step is that the positive pole of the power is connected to the switch’s load pin and LED light pin (+), the other load pin is connected to the device’s positive pole.

The second step is that the power’s negative pole is connected to the device’s negative pole and LED light pin(-).

Where to buy the mini LED push button switch?

You can purchase our products directly through Alibaba online, or through email communications to purchase this mini LED push button switch. Per product weight is about 0.05 kg.

According to customer’s quantity to decide the delivery way. One box package quantity is 50 pieces and one carton is 1000 pieces.

This mini LED push button switch is special and has no MOQ requirement. We can provide samples free of charge for your test.

Free button samples

Click to view our online store

If you are interested in our product and need it, or you need the samples, please contact us directly. Our email address is [email protected].

Quickly place an order online
Fill out my online form.