10MM Mini Red 230V Panel Mount LED Indicators

LED indicators parameters

Component name material
Lens PC plastic
Metal Body H59 brass or 304 stainless steel
Wahser T10 Cold Rolled Steel
Rubber Ring SIL silica gel
Nut H59 nickel plated brass
Housing PA66 nylon
Light Source LED
Resistor Metal film
Cable PTFE AWG22 0.3mm²
items parameter
Rated voltage 3V-780V DC or AC
rated current 20mA
rated power 0.2W
Insulation and voltage resistance 1800V
working life 100000h
electrical life 100000
cold-resistant -40℃
heat-resisting 80℃
Plug-in C2680 RoHS brass

What are LED indicators?

LED indicators means the product produced with LED as the bulb and placed on the equipment.

When the current passes through the machine and equipment, LED indicators will light up.

By this way, people can know that the equipment is in power status or working status.

The introduction of the 10mm mini LED indicators.

  1. The installation aperture of the LED indicators is 10mm. You just need to open a 10.2mm aperture on the equipment panel. Then put the product in the panel hole, and with the waterproof ring. Screw the copper nut to fix it on the panel, and it is waterproof.
  2. The product’s head material adopts PC material, which is high temperature resistance and good light transmittance. The inside of the plastic shell is designed with strips. When red LED indicators are illuminated, the lights give a beautiful strip light through the stripes, which is very bright and atmospheric.
  3. The metal shell material is divided into brass, stainless steel, and zinc alloy. The following are the distinction of the three materials.
  • The advantage of the product is that the product will not be changed or corroded under harsh environment. If it is used under the circumstance of sulfuric acid and salt water, we suggest you use 316L material, since other materials may be corroded, however, the cost of the stainless steel is higher.
  • The advantage of the brass metal material is that the appearance will be smooth and shiny after electroplating process. It will be very grand when installed on the equipment, which can improve the high-end degree of the product.
  • The advantage of the zinc alloy metal material is that it can be electroplated in a variety of different colors, such as red. The whole shell color is red, which is very beautiful and chic.
push button switch material

4. The product can produce various voltage by changing resistors and the value of the resistance, such as 2V, 3V, 5V, 6V, 12V, 24V, 110V, 220V, 380V, etc.

5. The product adopts non-polar double core LED, in the case of DC, it don’t need to distinguish positive and negative poles, which can be connected at will. The service life of LED can reach 50,000 hours, it can also produce a variety of different colors by changing the color of LED, such as green, yellow, blue, white, and so on.

6. The base plastic material is made of nylon PA66 with temperature resistance of 180 degrees, which is also flame retardant and environmentally friendly. The wire adopts PC material of 105 degrees. If you need high temperature resistant material, you can also change it into Teflon or silica gel wire with temperature resistance of more than 180 degrees.

7. The end of LED indicators wire can be connected with various terminals according to customer’s requirements. Such as 2.54 terminal, 2.8 terminal, 4.8 terminal, 6.3 terminal etc.

12V indicator light

How to produce LED indicators?

  • First step, cut off the LED pin, if it has positive and negative polarity, you must first cut off the lead of the positive LED lamp, then cut off the lead of the resistance, then connect the resistance to the LED with a copper tape machine. (Note that the body must be wearing copper machine with electrostatic bracelets, machine must take electrostatic measures. If don’t take the electrostatic measures, the LED lamp chip is easily damaged by electrostatic in the production process, and the LED will not light up. Especially those LED breakdown damage will light up in the test process, but their service life will very short, resulting in the LED indicator light not on.)
  • Next, cut off the pins of the LED and resistance, and then use a copper belt machine to connect the LED with resistance and wire. In order to make the connection of the LED, resistance and wire stronger.
  • Then weld the three joints with solder wire( be careful not to use rosin solder paste). Since rosin solder paste conducts electricity, please be careful when using solder. Thread the wire into the base, fasten the base and the wire with a machine to make sure the wire does not come off, then wear the LED indicators lampshade.
  • Finally, a power test is carried out to complete the process of LED indicator light with wire.
10MM Mini Red 230V Panel Mount LED Indicators

What size of resistor for LED indicators?

It is decided by the voltage of the LED indicators.

The usual algorithm is

Series resistance value=(circumscribed voltage-LED work voltage)/ LED work current *10

The unit of voltage is volt, current is ampere, and resistance is ohm.

Indicator light resistance

How to ensure the quality of LED indicators?

Filn has a professional LED indicators testing laboratory to ensure the stability and safety of product quality.

  • The voltage test bench of LED indicators, it often has electric leakage from metal LED indicators, which is very dangerous. If 1800 V does not break down within 5 second after passing the voltage test, there will be no such problem.
  • Waterproof tester, you can test the waterproof grade of the indicator light by the waterproof testing instrument.
  • LED indicators tension tester, by this instrument we will know whether the connection between the wire and indicator light will be firm.
  • Aging tester, by this instrument we will know other LED parts’ use condition of the indicator light.
  • Environmental protection material tester
filn sales-team

How to purchase the LED indicators?

You can email to us directly. There are 50 pieces in a box, the weight of each box is 1.2kg, and there is no MOQ requirement.

If you have custom patterns, you can also email us, we can customize according to your patterns. We will arrange the delivery within 3 days.

If you are an American customer, we will send DHL express. The conventional products will be arrive at your place in 3 days, and the customized products will arrive at your home in 6 days.

In addition to these 10mm LED indicators, Filn also produces various types of indicators, such as metal indicator lights and plastic indicator lights, which can be produced in large and small sizes.

If you have any questions about the indicator, please email us and we will give you a satisfactory reply with 12 hours. Our email address is

Filn online

Quickly place an order online
Fill out my online form.